Who are the redguard based on?
Who are the redguard based on?
Redguards seem to have an Arabian/ Ottoman base. Orcs are almost certainly Mongolian based. Bosmer could be considered Native American, with their value of nature and the like. Dunmer being comparable to the Feudal Japanese is some ways.
What faction is redguard?
| Redguard | |
|---|---|
| Alliance | The Daggerfall Covenant |
| Recommended Classes | Dragonknight or Nightblade |
Can you use Redgard on drywall?
Drywall Shower Walls Drywall (sheetrock) falls apart when it gets wet. Putting a product like this in a shower is just a bad idea. So if you see your contractor applying Redgard or another “waterproof paint” over drywall you might want to put a stop to things sooner rather than later.
Will Thinset adhere to RedGard?
You”ll be fine with thinset over Redguard on walls. It’s recommended for waterproofing niches, shelves, and entire shower walls when tar paper or poly are not used as a vapor barrier behind the CBU.
Do I need to use RedGard over Hardibacker?
You really don’t need the RedGard, but the more protection the better…so go for it. And yes, you can do the boards beforehand. But, hit the filled seams & screws (your weak points) as soon as a panel is ready to give it some time to setup. You’ll have to wait for the fills to dry or at least setup anyway.
Do you need to use RedGard over cement board?
No. If you plan to use Redgard, follow the Redgard installation instructions. This goes for all the products you use in that shower too, like the drain, liner, backer board, mortar/thinset, grout, caulk, etc…
How long does Thinset need to dry before RedGard?
24 to 48 hours
Does Hardibacker need to be waterproofed?
Passing ANSI 118.10 for waterproofness, HardieBacker® 500 Waterproof Cement Board protects tile installations and wall cavities from moisture penetration, eliminating the need to spend extra time applying waterproof coating across the entire surface area of your wall project.
Do you need to seal Hardibacker before tiling?
Contrary to popular thought, tile and grout are not waterproof, and some moisture will penetrate even if sealant is used. If you decide to go this route, no sealant will need to be applied on top of the backerboard, as this could trap moisture between the two layers of waterproofing.
Can you tile straight onto Hardibacker?
Both 6mm and 12mm HardieBacker cement boards can be used on masonry walls. HardieBacker can take up to 200kg of tile hanging weight per m2 so almost any tile can be fixed. Once secured cover the joints with Alkaline-resistant tape and feather the tile adhesive to leave a 150mm wide joint.
Do I have to put Thinset under Hardibacker?
Thinset is absolutely required beneath backer-board on a floor. Also, backer-board provides no structural strength at all. You can not install it directly over a 1x subfloor; that is way too thin and will deflect. It does not sound as if you have a quality-minded contractor.
Do you have to tape seams on Hardibacker?
Do you need to tape durock? For tile backer board such as Durock, Wonderboard, Hardiebacker, Permabase, and others the seams between the board need to be treated with 2-inch alkali resistant mesh tape. Then a coat of thinset gets flat troweled over the seam.
Which is better durock or Hardibacker?
Durock can be used for both internal and external situations. Durock is a reliable cement product that contains glass mesh. It is the heavier of the two materials, which means it is more difficult to use and maneuver. HardieBacker is much more light, and it is also the best selling brand of cement board available.
Should you wet cement board before tiling?
Whenever you’re laying tile on a wood subfloor, you need to first install cement backerboard to prevent leaks and water damage that could harm your flooring and the structure of your home. Unlike wood or drywall sub-surfaces, cement backerboard will not rot, warp or grow mold and mildew when exposed to water.
What kind of Thinset do you use for Hardibacker?
Latex or acrylic modified thinset (complying with ANSI A118. 4). Dry-set mortar for use between subfloor and cement board only (complying with ANSI A118.
What side of Hardibacker board faces out?
This is the smooth side of the board. This indent allows you to tape with fiberglass tape and thin set compound to give you a solid surface in which to place the tile. So smooth side out.